|Product Type||Shipped Product|
|Number of reviews||0|
SBC CHEVY STAGE 2.0 HYDRAULIC ROLLER CAM 383 CUBIC INCH ENGINE 505 HP STREET ROD SETUP.
RUNS ON PUMP GAS.
This engine is fully assembled from intake to oil pan.
ROLLER BLOCK WITH SPLAYED MAIN CAPS.
FORGED 4.030 BORE WISECO PISTONS, SCAT 3.750 STROKE CRANK, AND 5.7 or 6.0 SCAT RODS. NKB ALUMINUM HEADS.
FULLY ASSEMBLED FROM INTAKE TO OIL PAN.
4.030" BORE X 3.750" STROKE
GM ROLLER BLOCK WITH 4 BOLT MAIN CAPS.
- NKB ALUMINUM ALLOY HEADS.
- HOWARDS ROLLER CAM. A CUT ABOVE THE OTHERS.
- CLOYES RACE BILLET TIMING SET. THE VERY BEST CLOYES HAS TO OFFER.
- SCORPION RACE SERIES ALUMINUM ROCKERS 1.5 OR 1.6 RATIO.
- SCAT CRANKSHAFT, CLEVITE BEARINGS. BALANCED ON OUR CWT BALANCER TO BELOW 2 GRAMS.
- SCAT RODS WITH ARP 8740 CAP SCREWS.
- WISECO PREMIUM FORGED PISTONS. 800+HP RATED.
- MELLING M-SELECT SERIES OIL PUMP WITH M-SELECT DRIVE ROD.
- CHAMP 5 QT. OIL PAN WITH OIL CONTROL SYSTEM. 8qt. AVAILABLE AS AN UPGRADE.
- PRO-RACE BRAND DAMPER.
- TWO YEAR WARRANTY.
This engine is designed for street/strip use. Pump gas friendly.
See our other listings for the fully dressed out turn-key version.
Two year warranty, see details below.
This engine is designed to have a high level of drivability, or street manners. Cams #3 and #4 are our favorites for offering exceptional low end and mid range performance plus max drivability without needing to deepen final gearing or the need for a high stall speed torque converter.
If you choose to go with the Hurricane single plane intake and the first choice cam with 1.6 rockers, it will bring the hp numbers up to approx. 505 or more. We do not recommend the single plane intake combined with cam choice 1 on any car that is over approx 3,200 lbs and/or cars with a steep (tall) final gear.
Please read the cam info provided below on the four cam choices before purchasing this engine. It is very important that you choose the correct cam and intake for your car and its intended purpose.
Here are a few good reasons why we think the 383 engine is a better choice than the 350 engine.
1. The 383 will accelerate most medium to heavy cars dramatically quicker than the common 350's on the market. The main difference between a 383 and the 350 is that the 383 torque comes in much lower. The difference is so dramatic that you would estimate the engine to have a much higher horsepower rating than it actually has. If you're not familiar with the 383 engine, do an internet search on SBC 383 vs 350, and you will be convinced of the difference.
2. The exhaust note that this engine produces is much deeper than that of any of the smaller cubic inch engines on the market. The difference is dramatic to say the least.
3. This engine can be installed in medium to heavier cars without killing acceleration, having to deepen the final gear, and needing a huge stall converter. This engine will accelerate a 3600 lb or heavier car much better than the 350.
4. Very low maintenance, decent drivability, yet costing only slightly more than building a 350 street rod engine. Horsepower will vary, depending on cam and intake choice. You have up to four different cams to choose from, and two styles of intake manifolds plus two rocker ratios.
5. Longevity, reliability and low maintenance. You don't have to turn the engine to a critical rpm range to produce its max hp output. There is nothing unsafe about running an engine that's as well built as this up to approx. 6,150 rpm. Our NKB aluminum heads use very high quality hardware. The Wiseco Racing pistons are rated at 800+hp. The protection against detonation is at its highest with these type pistons.
6. Should you ever decide to sell your car, the resale value of a street rod with a 383 engine is very desirable compared to those running 350's. No 350 can be built up to the level of a 383 while running pump gas with the same compression. The power and torque numbers down low in the rpm band are what make the 383 such an incredible engine, compared to the 350.
We do a full test run on every engine we build on a test mule. The engine is run for two intervals of 15 minutes each, and every possible issue is addressed. When you install the engine, you must verify that the timing is set at the correct value, and the fuel to air ratio must be verified. We also include an engine stand like the one pictured, wheels included, and an engine lift plate.
As of 9/15/2013 we completed installation of our brand new Super Flow 902S dyno. In the past, we outsourced our dyno work. We were unable to do the research and development we truly wanted, and this prompted us to make the $105,000 investment. It’s been one of the best investments we have ever made. Every aspect of our engines can now be monitored, calibrated, and tuned. Best of all, we can now see what combos generate the best power, with consideration to drivability.
One thing we have noticed is that the de-tuned engines with different cam and intake combos certainly do have less top end horsepower than expected, but the torque increase in the low rpm range is much greater than in the higher horsepower setup. This increase in torque down low is what you want if you’re sporting around on the street, rather than all out racing. The de-tuned version of this engine will also allow you to set the car up closer to stock and increase drivability to a very high degree. Throttle response is also noticeably better.
The build sheet is as follows:
The bare block is a fully machined re-manufactured true GM late model roller block. 1 pc. rear main seal style and designed for street or strip applications. All internals and external items in this engine are 100% brand new.
The compression range will be approx. 10.5:1. This setup will certainly generate the highest horsepower when coupled with our cam choice # 1 or 2. We do not see any problems with a 10.5:1 compression range in light to medium weight cars. For those choosing cam choice 3 or 4 we will lower the compression ratio slightly. The lower compression is all that's needed with the smaller cam, and this further increases reliability to a great extent. Fuel requirements can be lowered to mid grade 89-91 octane with the reduced compression, but do also consider the many other factors that increase the need for octane, such as outside temps, altitude, ignition timing, vehicle weight, gearing, payload, etc. We would prefer that you use premium fuel regardless of what setup you have choose. Were more or less on the thin line between mid-grade and premium fuel requirements with the reduced compression setup. We would prefer you run premium fuel.
This 4 bolt main bare block used for this engine is an OEM late model GM roller block that has been fully reconditioned/re-manufactured. The rotating assembly and all other parts except the block are 100% brand new. This engine is set up with your choice of several different hydraulic roller cams.
The blocks used for building our Stage 2 roller cam 383 do have four bolt main caps.
These blocks will accept mechanical fuel pumps.
As you can see in the picture above, this is a true roller block.
Listed below are all the machining procedures performed on this block. These are 1 pc. rear main seal style.
Mains have been line-honed to factory specs. This important procedure is often skipped, and failure to do this usually results in a short-lived build.
Block has been bored and torque plate honed. The use of a torque plate when honing is a very important procedure, and many blocks on the market don't have this performed.
Pictured below is the rotating assembly that comes in this engine.
(file photo, actual parts may vary, see details below)
The photos above and below are file photos. Actual appearance may vary. This picture is to give you an idea of parts used in the rotating assembly portion of this engine. All parts are brand new, first line, unblemished, and balanced in house.
READ THIS LISTING COMPLETELY BEFORE YOU BUY ELSEWHERE!
Connecting Rod Specs.
Piston & Ring Specs.
Bearing, Damper, and Flexplate Specs.
Flat or Dish top pistons will be used depending on Cam selection.
The Wiseco fully forged pistons are rated very high in the street/strip performance industry. They offer several price levels of pistons, starting with the Pro-Tru Street version made with 4032 forged alloy. The next level up would be the Professional series that are much more expensive and made from 2618 aircraft alloy.
Our custom made Wiseco pistons are very close in comparison to the Professional series as they are made using the 2618 aircraft alloy and have fully machined crowns.
Our Wiseco Forged pistons are custom designed with an increase in compression height. This has many advantages. Here are a few facts about compression height and deck height.
Our custom made Wiseco pistons have a compression height that is .015 taller than nearly all catalog pistons on the market. We find this to be a very valuable feature.
Another good feature about our pistons having a taller compression height is that the ring land above the top ring is much stronger by being .015 thicker. When pistons encounter the effects of detonation, it is not uncommon to see pistons with the ring land above the top ring broken off. The thicker ring land also makes a better heat sink.
You may have noticed that our Wiseco custom made forged pistons are referred to as Racing Pistons on the package. This does not mean that the pistons are for racing only. This is a generic term, referring to their ability to be used in high performance applications as well as for street rod use. These pistons are perfectly designed for use on the street, as well as for medium to upper level drag racing.
Our custom made Wiseco forged pistons are made from 2618 aircraft alloy. We find this alloy to be much more suitable for high performance engines than the common 4032 forged alloy. You will usually see the higher end pistons on the market using 2618 aircraft alloy.
Why go with 2618 forged pistons? If you encounter certain tuning issues, detonation is highly probable, and its effects can cause severe damage to your engine. The 2618 forged piston is able to withstand the damaging effects from detonation to a higher degree than the lower cost 4032 forged pistons, especially non-forged hypereutectic pistons such as Speed Pro or Keith Black, and many others.
We have built approximately 3500 engines using the Wiseco pistons. The engines have been for street rod and strip use. We have seen no problems, nor have there been any complaints. They are an excellent product in every respect.
These pistons are also suitable for use with nitrous or blower setups.
The pictures below are file photos of our Wiseco pistons. Flash glare on the piston top seems to have enhanced the milling marks. These are hardly visible with the naked eye.
Flat or dish pistons, depending on cam choice. 5.7 or 6.0 inch piston and rod combinations available.
HASTINGS HIGH PERFORMANCE MOLY RINGS
The picture below is a generic file photo of a Scat crankshaft.
Some of the benefits of the Scat crankshaft:
The material used in this crankshaft is manufactured from an exclusive Space Age material that was designed for high strength and fatigue resistance. The Scat cranks are the best value you will ever find. The Scat crankshafts are the best way to build a strong bottom end for, street rods, dirt and circle track racing, and drag strip racing.
We now use the Clevite bearings in our engines.
Our choice of rods are the Scat Pro Stock rods with ARP-8740 cap screws.
We use genuine Scat rods with ARP cap screws in all of our engines. Our Scat rods are bronze bushed, and unlike some Eagle I beam rods, these are fully forged 4340 alloy.
We have noticed some engine builders using low cost generic rods and crankshafts in their engines. These non-branded, (no-name) products are often poor quality in many ways. You will notice many of the low end engine builders fail to mention the actual brand of the rods or cranks used in their engines. Upon further investigation you will find such parts not to be a branded name product. They may label these parts with a name, but one that is totally unrecognizable in the industry. Our experience in years past with such rods and cranks has been disappointing to say the least. Besides the obvious issues such as incorrect sizing and machining that is difficult to correct, the questionable alloy these items may be produced from and the potentially incorrect heat treating methods used, could prove to be disastrous. Little can be done to verify this and nothing can be done to correct it. Failures of such critical parts will usually result in catastrophic damage to the engine. As you may have noticed, this is why we specify the brand name, and series of every part used in our engines.
Many of the inferior "no-name" rods on the market will also have "no-name" rod bolts in them. We have seen these bolts before, and they are very low quality. They don't have ARP's rolled thread design, and they don't torque down with the same characteristics as a genuine ARP bolt. It's not just a matter of having a different brand bolt in the rods; these bolts are low quality in many ways. They have been known to fail in engines to a much greater degree than a high quality rod bolt, and this failure usually causes catastrophic damage in the engine. Beware of rods that don't mention the rod bolt brand. As far as we're concerned, ARP bolts are the only brand we would ever use or accept in a set of rods.
Genuine ARP 8740 cap screws.
PRO RACE BRAND HARMONIC DAMPER, 6.75 DIAMETER, INCLUDED.
Pro-Race brand damper is used on all of our engines.
INTERNALLY BALANCED, 6.75" DIAMETER REDUCED ROTATIONAL MASS, OFFERS EXCELLENT CLEARANCE.
1.52" THICKNESS, 2.38" THICKNESS WITH HUB
HEAVY DUTY SFI RATED FLEXPLATE MADE IN THE USA INCLUDED.
This SFI flexplate is made in the USA and will resist cracking and warpage to a very high degree. One good telltale in identifying a low quality flexplate is the lack of welding on each side where the plate mates to the ring gear. They usually have a pale grey color to them, as they are not coated, and will rust quickly. Ours are welded on both sides, and are much thicker than an OE plate, and are zinc dichromate coated.
We do offer this engine with a manual flywheel. In most cases we do have both sizes, 153 and 168 tooth, available.
Pictured below is our ABS crank polishing machine in action. We polish the crank on every engine we build. This extends bearing life, keeps oil cooler, and with the reduced friction, a slight increase in horsepower is gained. Many machine shops fail to do this. The finish on most cranks is at the bare minimum of acceptance, and we know this can affect bearing life. We have measured the RA finish with our profilometer, and found it to be as high as 25 RA finish on many of the cranks. We bring that number down to below 10.
Our CWT 5500 Balancer.
We do our own balancing with our new state of the art CWT 5500 Series balancers. The CWT 5500 is the ultimate for precision balancing. We now have three of these in our machine shop. We consider this machine to be highly advanced compared to the Hines balancer we once used. We balance every rotating assembly we sell within 2 grams or less at no extra charge. A balance sheet is included with your engine.
Three new CWT balance machines under one roof is a rare sight.
Our crew wrapping up for the day. Pardon the mess.
NKB 200cc ALUMINUM HEADS
Our new NKB-200 heads have been designed especially for us. After receiving many recommendations from our engine builders, we came up with the best quality, best flowing heads on the market relative to cost. The only way you’re going to get a set of heads that flow as well or better will be to spend at least double the cost or more. We have installed these heads on all of our 383 and 406 engines for the past two years. Many of these engines were dynoed on our new Superflo dyno. The engines had every possible combination of cam, intake and carb. The results have been amazing. These heads are excellent in design and quality. Our choice of hardware and precision assembly also contribute to the performance and reliability of the heads.
In the flowchart below, the NKB-200s are superior to the Procomp heads in flow rates, and also edge out the Dart SHP heads on the intake side. The intake numbers are far more important than the exhaust. The overall average flow numbers on the NKB-200 heads are higher than most any brand of non cnc'd cast aluminum heads on the market.
The difference in horsepower and torque generated by the NKB heads is monumental compared to most all of the low cost sbc heads on the market. We offer four different cam choices with our 383 engine.
Here is a rundown on the hardware used in the NKB heads and the assembly process.
The retail cost at most High Performance stores on the PBM Competition valves is $239
We are now using the Competition Series PBM valves in all of our 383 and 406 engines. These are considered a high end valve. These valves have an undercut and backcut feature.
The backcut feature reduces valve weight by an average of 12.5 grams per valve. This weight reduction of approx. 208 grams off the complete set of valves has a monumental effect on acceleration, deceleration, and valve train life. It may be difficult to understand how this works, but rest assured, this is a huge reduction. The valve spring compression and rebound action will remain stable for a much longer time running lighter weight valves, as well as reducing valve float.
The backcut feature is not be mistaken for undercut. These valves have both features. Backcutting is an additional radius, but located on the head of the valve to increase the flow numbers and reduce valve weight. The flow increase is approx. 3-6 points on the flow bench, and possibly more, depending on the initial flow rate of the heads.
According to one of our machinists who built Winston Cup engines for 15 years, the exhaust valves had an additional radius cut on the outermost edge that allowed a better escape of the exhaust gas. This cut on the exhaust valve is in addition to the back-cut feature. The competition series are made from a much higher temp alloy than most other stainless valves. There are at least three levels of stainless valves on the market, excluding those used in very high level racing such as pro-mod. The PBM competition series is compared to the highest level of those three. As a final note, backcutting a set of valves is said to improve flow in the low lift area, and this is most desirable on street rods.
Comp High Performance Dual Springs, Part Number 987-16
Our Comp springs are 1.43 diameter, with an inner spring and internal damper. Others are using springs that are much smaller in diameter. Smaller diameter springs may be in the correct spring pressure zone, but they usually have a shorter life. Comp springs are made in the USA. All of our engines using the NKB heads use these springs. Spring failures are near non-existent.
COMP CAMS "POSITIVE STOP" VITON VALVE STEM SEALS. # 529-16
Comp 10 degree machined valve locks.
We use only Comp Super 10 degree machined locks. Our head builder noticed the low grade locks on the market fit more loosely than he felt they should, not to mention the possibility that they were made of inferior metal. He envisioned the engine being much more prone to dropping a valve at high rpm. Using these locks, we have yet to have an engine drop a valve due to a valve lock failure.
Comp Cams retainers # 75740-16 and Comp Cams ID locators Part number: 4771-16
Our Comp Cams retainers # 75740-16 and Comp ID locators # VTH-4771-16 are made from 4130 chromoly steel. These retainers have a perfect fit with the Comp valve locks. We have used these on all of our engines for many years, and have had zero failures.
We hone all of the bronze valve guides with a ball berry flex hone to establish not only perfect clearance, but also a semi cross hatch finish for oil retention. We finish off with a natural bristle brush. The heads are then placed in our parts washer and cleaned with high pressure hot water, then pressure dried. Before installing the valves, we apply a heavy coat of engine assembly lube to the valve stems. The coating on the valve stems is essential to protect the bronze guides from gaulding on initial startup.
Our next step is to set the spring pressure to a predetermined pressure using a spring height checking device, most suitable for street rod use. The springs we are using allow for a near perfect seat to nose ratio. Be warned that some sellers of aftermarket heads may not be checking the installed height when assembling the heads, and may not be setting them up to the correct pressures. We have a full scale machine shop with several very knowledgeable engine builders that know and fully understand how to properly assemble a set of heads. Combine the possibility of poor assembly methods with incorrect or low grade hardware, and it is easy to see how failures can result.
Head gaskets are Fel Pro 1003 premium race grade series, and ARP head bolts, and rocker studs.
Scorpion Race series 1.5 OR 1.6 ratio roller rockers with 7/16 ARP rocker studs. We recommend the 1.5 ratio for better low end response and extended valve train life.
THE BEST HIGH PERFORMANCE RACING ROCKER ARMS MANUFACTURED IN THE USA.
We were amazed at the low level of sound produced in the valve train when we did a test run using our first set of Scorpions. We attribute this quiet operation to the close tolerances in the trunnion section. The trunnion barrels are also micro polished.
The rockers have a lifetime warranty. The aluminum body is made from a 7000 series aircraft alloy. Most rockers have a considerable amount of side play in the trunnion section, and may have an excessive amount of needle bearing clearance. The Scorpion does not have much of a loose feel in the trunnion. Many round track and drag racers run these at very high rpm levels and even run them on solid roller setups. With the milder spring pressures of our engines, these rockers should last a lifetime.
All Scorpion Rockers Feature:
Needle Bearing Fulcrum and Roller Tip, Centerless Ground Trunnion, Centerless Ground Pin & Roller, Burr-Free Thru Hole in Trunnion, Large Machined Seat, Thick Walled Adjusting Nut, Pedestals Machined from Solid Steel, Black Oxide Coated Steel Parts, & 100% CNC Machined.
If you’ve read our warning on engine builders using low grade no-name rods and cranks, a very similar situation exists in the roller rocker market. We do not use or sell off-shore, (no-name) roller rockers, period. They have proven to be faulty in many ways. The center trunnions are not polished, nor is the center of the roller tip true to size or polished. Metal fragments are often left inside the trunnion housing and will cause destruction of the needle bearings. The aluminum alloys used are never aircraft aluminum alloys as are used in all USA made roller rockers. They often mention the alloy as being 6061, and that is a very soft form of aluminum. The 6061 alloy used on these will assure rocker-flex on any higher than stock spring pressures, and this will affect performance. The pins and keepers that hold the parts together are often of poor quality and improperly installed. The front roller will usually scoot along the valve tip, as it can't roll properly due to rough internal surfaces.
We have honestly seen valve tips that were scalloped out due to the front roller dragging across them. This will cause the valves to side-load against the valve guides in the heads and surely cause damage to them if run like this for very long.
We have scrutinized these products in the past and found all of the above problems, and I can tell you there are most likely many more. We would not use them in an engine under any circumstances. You will also see many of these rockers made from stainless on the market. They use a very low grade stainless that actually has a near non-existent amount of nickel in them, but that's not the real problem with them, as stainless steel has no advantage over high grade heat treated steel when it comes to a roller rocker. The lack of hardness of the rocker body is the real problem. The problems with these stainless rockers are the same as mentioned above. These are the roller rockers you see on the market for around $119 and up to $169 for the so called stainless ones. They are pure junk, in our honest opinion. They could possibly be used on a budget back yard stock build up that has a very low spring pressure, with a cam that has very low lift, but then you would be better off with the stock stamped rockers on such a build.
We have heard of many engines using these rockers that came apart and spilled needle bearings into the engine, only to end up in the oil pump. It seems like some engine builders do not care how long the parts in your engine last, or they simply don't know this. I can tell you for sure that using such low grade, "no-name" roller rockers is asking for trouble.
We use Scorpion, Comp Ultra Pro Magnum, and Comp Gold Arc rockers in all of our engines. The difference in these compared to the low grade no-name rockers on the market is huge. Do a Google search on this subject and you will know then what we’re talking about.
DELPHI ANTI PUMP-UP LIFTERS
We have had a vast amount of experience with the Dehphi hydraulic roller lifters. They are a good quality lifter and work well in our engines.
Howards Brand Chromoly One pc. Pushrods.
Howards brand are the only type of pushrod we use in our engines. Made in the USA from 4130 chromoly steel. Regular hardened pushrods will most likely flex in the engine when running above normal RPM ranges, and risk bending under high RPM. These do not have the welded ball on the end. We only use the swedged one pc. design, which is a well proven design far superior to the style many others use in engines. 4130 chromoly steel is also much stronger, and will resist flexing. When a pushrod flexes in the engine, you lose lift. Don't be misled by the term "hardened," as this is nothing more than a stock style low cost push rod. They will flex in the engine or possibly bend permanently.
The timing components are the Cloyes Race Billet double roller timing set. Part # 9-3645X3
We use the top of the line Cloyes timing set. We use this exact set in our 421 and 427 SBC engines. The difference in quality is dramatic compared to the common true double roller setup. The chain is made in Germany, and the sprockets are hardened billet steel (upper and lower) and made in the USA. These sets are hand matched for selective sizing.
The cost on this setup is approx $129, about four times the cost of the low level budget timing set used by many other engine builders. Should you ever want to confirm that this is what is actually in your engine, you can remove the timing cover, and you will notice the upper gear has a fully array of lightening holes.
It may be overkill to use this expensive setup, but the attraction, besides being the most precise, is that it comes in three sizes. Many times a regular timing set will have too much or too little tension in the chain. If the mains have been line bored or line honed, this can affect the tension of the timing chain.
This top of the line timing set is offered in three different chain tension setups, allowing us to set it up perfectly every time. One more benefit is that timing accuracy is very precise and will remain that way. This timing set will likely last for the life of the engine. This is what you will find in most solid roller engines, as they have very high spring rates, and create an enormous load on the chain and gears, compared to non solid roller setups.
Cam choice #1
PART # 180255-10 This is a hyd. roller cam for use in OE roller blocks.
Valve lift with 1.5 Rockers: Intake .510/Exhaust .530
Duration @.050": Intake .231/Exhaust .235
Lobe sep. angle: 110º
This cam choice (1), coupled with our single plane intake and our flat top forged pistons with 1.6 rockers, will produce right at 505 horsepower at approx. 6,150 RPM. We recommend the dual plane for better drivability, and throttle response. The dual plane intake will move the torque down lower in the rpm range. The single plane intake would allow the engine to make its peak advertised horsepower at the peak rpm, but these type intakes move the torque band higher up in the rpm range. Expect a slight loss of top end power with the dual plane intake, but low speed drivability and cruising are greatly improved.
The single plane intake is not recommended for use in vehicles weighing over 3,600 lbs unless your vehicle is setup with a somewhat deep final gear. The rockers used on our test engine were our Scorpion Race Series roller rockers. Our cam timing components were left in the straight up position. Ignition timing was set at 34 degrees total and 93 octane fuel was used. During very hot weather, total timing should be set at 31-32 degrees. A final gear of approx. 3.73 or numerically higher, and a stall of approx. 2,600-3,000 would be highly recommended.
Below are our dyno results on one of our 383 engines with cam choice # 1 with a single plane intake.The single plain intake would have produced a higher hp number. Results will vary depending on intake choice. The horse power numbers will usually improve anywhere from 5-10 more than what the dyno results show after the rings have fully seated.
Official Dyno report on our 383 engine with cam choice #1 and a single plane intake.
Cam choice #1 and a single plane intake.
If you choose cam choice 1 with the single plane intake combination, it is highly recommended that you upgrade the ignition system to an MSD Pro Billet distributor and CDI unit. You should also purchase the SS Quickfuel carburetor for optimal performance. These important upgrades are essential for improved idling and overall performance. If you do decide to use the MSD Pro Billet distributor, we suggest you use the black timing degree bushing to increase the initial timing and possibly the lighter springs to control how soon the mechanical advance comes in. You may even "lock-out" the distributor, depending on your car's overall setup. The CDI unit will make a huge improvement in how the engine runs at idle and low speed cruising, as well as high rpm operation. The SS carb allows you to adjust and control the idling and low rpm cruising quality to a much greater degree than the regular vacuum secondary carb. The acceleration and overall performance is greatly enhanced with the SS Series carbs.
There is one more upgrade that I feel would enhance performance and add stability and longevity the valve train. The Tie bar lifter upgrade is essential for those that choose to run hard. The oe drop-in roller lifters used in this engine are a decent lifter but will not withstand hard use and/or the max rpm rating for any extended time. Any over-revving of the engine beyond its peak power may bring on valve float. The Howards Tie Bar lifters will not only improve performance but also allow the engine to operate very well in its peak rpm range. They will also maintain valve train stability for several hundred rpm past the peak rpm rating for this cam setup. This is a very nice upgrade for any street rod running into the upper rpm ranges.
Cam choice #2
PART # 180245-10 This is a roller cam for use in OE roller blocks.
Valve lift with 1.5 Rockers: Intake .500/Exhaust .510
Duration @.050": Intake .225/Exhaust .231
Lobe sep. angle: 110º
This cam choice (2) is the perfect all around setup for those wanting a decent bottom and mid range while still generating excellent power at the top. Horsepower rating would drop to approx. 470-475 with this cam when using the single plane intake and 1.6 rockers. This setup will generate its peak power at approx. 5950 RPM.
If your car is in the medium weight range or up to approx. 3,800 lbs, and you want slightly better streetability, then this is a good cam choice. You still want to keep the final gear ratio at 3.55 or numerically higher. You may choose 1.5 or 1.6 rockers with this cam, but we recommend the 1.5 rockers if you would like to further improve low end response.
This cam should be paired up with the dual plane Crosswind intake for better drivability. The single plane Hurricane can be used, but the dual plane will have much better bottom end and mid range response. You can also expect a longer valve train life with this cam compared to the larger cam choice # 1.
Below are our dyno results on one of our 383 engines with cam choice # 2 with a single plane intake. Your results may vary depending on intake choice. The horse power numbers will always improve anywhere from 5-10 more than what the dyno results show after the rings have fully seated.
Official Dyno report on our 383 engine with cam choice #2 and a single plane intake.
Cam choice #2 and a single plane intake.
Official Dyno report on our 383 engine with this cam choice, 1.6 rockers, and a single plane intake.
Cam choice #3
PART # 180315-10 This is a roller cam for use in OE roller blocks.
Valve lift with 1.5 Rockers: Intake .465/Exhaust .470
Duration @.050": Intake .209/Exhaust .215
Lobe sep. angle: 110º
This cam choice (3) has a lower lift and duration than the other two offered above, and is highly recommended for use in heavy cars or full size sport trucks. The low end response with this cam is very good. Horsepower rating would be approx. 425 at 5,500 RPM with 1.6 rockers and a single plane intake.
The rule of thumb for cam size: the smaller the cam in a given application, the better will be the low end response. One more benefit to the smaller cam is the reduced requirements for lower gearing and higher RPM stall converters. A final gear ratio of 3.30 would be acceptable with this cam. The bottom end power would be much better with this cam than the two other choices above.
This would be the only choice for running an overdrive transmission such as the 700R4 cruising at around 2000 RPM in overdrive. A stock stall converter may be used with this cam, but for improved acceleration a 2000-2250 stall is recommended especially in heavy vehicles with a tall final gear.
Valve train life is greatly extended with this cam as compared to the others, and drivability is at its best. Low and mid throttle response is very strong. This cam choice will also produce the greatest amount of vacuum at idle compared to those listed above. You may run power brakes with this cam, and it may allow the use of the vacuum advance for improved low end power and fuel mileage.
If you need help in selecting a cam to suit your needs, feel free to contact our tech. department at 423-722-5152.
You have a choice of single or dual plane intake. The single plane intake (1st pic below) should only be used on cars that are very lightweight and have good hood clearance.
Dual Plane Intake shown below. This is a large runner dual plane intake. They make excellent mid range power.
Pictured below is the Edelbrock Performer EPS dual plane intake. If you're going with cam choice # 2 or 3 and require more bottom end power, we strongly recommend this intake. This intake offers incredible low end response and has excellent hood clearance for those installing this engine in a C3 Corvette with a non-cowl stock hood.
Polished intakes also available.
304 STAINLESS ALLEN HEAD INTAKE BOLTS ARE USED ON ALL OUR ENGINES.
Pictured below are our most popular valve covers. They are fabricated aluminum, and very high quality. You may select from any of the valve covers we have listed at no additional cost for your engine.
RETRO STYLE FINNED. OUR SECOND MOST POPULAR CHOICE.
THE RETRO FINNED VALVE COVERS CONTRAST NICELY WITH THE CHROME AND POLISHED ITEMS.
POLISHED ALUMINUM TIMING COVER.
We use only Felpro seals and gaskets with our timing cover.
Melling M-Select Oil Pump, and M-Select Drive rod with ARP stud.
The M-Select series oil pump by Melling has several important upgrades compared to the regular Melling M-55 Series. The gears are billet steel, and the body is stronger, coated with corrosion-resistant nitrite. This oil pump also includes the M-Select drive rod. Both components are far superior to the regular Melling oil pump and drive rods used by most other engine builders.
Champ premium oil pan.
Pictured below is the oil pan included with this engine. The Champ oil pan used on this engine has a 5 qt. capacity. It has an elaborate oil control system. Features windage tray, crank scraper, .055 gauge outer shell. Champ oil pans are made in the USA. All of our engines will come with the Champ oil pan. We also offer the 8qt Champ pan as an optional upgrade. If your car will not allow the use of the large capacity Champ oil pan.
We do not use the knock off oil pan gaskets on the market. Felpro premium oil pan gaskets are used on all of our engines.
We use this premium studded mini nut set for oil pan and valve cover fasteners. The nuts have a serrated face and built in washers. This is the ultimate set for securing the oil pan to the engine and is far superior to the typical bolts used by most other builders. We use this set on all our engines.
Our new 383 engine is premium pump gas friendly, with very good street manners. NEVER run regular 87 octane in this engine, premium only unless you have opted for our de-tuned version with a reduced compression ratio. Should you ever hear any sign of pinging or clatter in the engine when accelerating, reduce timing one or two degrees.
We include an engine lift plate and heavy duty engine stand with casters with every engine we build.
IMPORTANT NOTE ABOUT DE-TUNING.
For those with very heavy vehicles, such as 4x4 quad cab trucks, 3/4 ton trucks, and crew cab/ex-cab trucks, Suburbans, plus trucks that may do light to medium trailer towing, we strongly recommend the de-tuned version of this engine.
For those wanting to run a supercharger, we recommend our extra deep dish pistons with the 75cc heads regardless of the vehicle.
Our machinists have many years of experience in building racing engines. This very critical work is done to exacting specs and with great care. Many vendors do not have machinists with the experience or the proper equipment that we are fortunate to have. We have built engines that cost upwards of $50,000. All of our engine builders have been in the engine machining and engine building line of work for their entire working lives. Their ages range from 38 to 65. We have a total of seven machinists/engine builders.
This product does not have any reviews yet.